I, too, had this problem and found that the only solution was to reboot OpenSprinkler. I also run HomeSeer, and developed an event to recognize when OS was offline to warn me. I tried any number of approaches, including an access point that was just 10 feet away. I finally gave up and switched to OpenSprinkler Pi.You must disable its DHCP-Server, if You have another Router (Your main Router) with DHCP active. The best and easyist way is disable DHCP on Your OS an give him a static IP adress: e.g. main router is 192.168.0.1 an OS should be 192.168.0.100 and HTTP-Port 80: OS settings. Enable DHCP: No.Same thing here. Opensprinkler Android app does not load. It just stays there with the Opensprinkler logo and then it goes black and stays like that. I can control my OSPI fine via Chrome on my phone. Huawei Nexus 6P Android 7 stock. I tried this on my son’s Motola Nexus 6 Android 7 and it loads fine.Its simple, after speaking with DAB , the pump regulates pressure in the line as the solenoids are opened by open sprinkler controller than pushes water to the desired zone. Once the zone solenoid turns off the water pressure in the line signals the pump to turn off. There is a delay of 10 sec which is standard from the manufacture and can be ...Jan 7, 2017 · OpenSprinkler Bee (OSBee) is an open-source, WiFi-enabled sprinkler controller for latching solenoids. It is suitable for garden and lawn watering, flower and plant irrigation, hydroponics, and other types of watering projects. It comes with built-in WiFi, OLED display, 3D-printed enclosure, and can switch up to 3 zones independently. It is …Nov 29, 2013 · OpenSprinkler Pi. Watch on. If you hate watering the garden but enjoy messing around with computers, OpenSprinkler Pi is a no-brainer. It’s the cheapest and most configurable system of its type I’ve come across, it’s open source (and this means that Ray’s not the only person working on it – tools from the community like Rich Zimmerman ... Keymaster. There are two ways: the first is to do it the ‘hardware’ way: you can insert two zone wires into the same port, and those two zones will always turn on or off together (they are parallel). The other way is what you’ve already experimented with, the ‘software’ way: you can set each zone as ‘parallel’ zone (uncheck the ...The application allows you to automatically detect and control your OpenSprinkler irrigation system(s). OpenSprinkler is an open-source Internet web-based sprinkler timer / …Jun 6, 2019 · In the settings popup, click the Advanced tab and select “GPIO” as the station type. You can now select the gpio pin that you want to toggle when this station needs to water. Make sure you then wire up that gpio pin to the corresponding relay. You may need to swap the Active High/Low setting in the Advanced options depending on your ...May 20, 2020 · I have created two prototype board variants from Opensprinkler in Kicad. The first one based on the TTGO V2.1 1.6 (ESP32 Lora Board) and the second a dual board that can accommodate an esp32-wroom or an ESP-12E (ESP8266) plus a lora E22-900M3DS-SX1262 module.For OpenSprinkler 3.x only — one major step forward is the support of OpenThings Cloud (OTC) token, which allows remote access via the OTC cloud server. This eliminates the need for settings up port forwarding, which has been a pain for manual users. OTC has been enabled for our OpenGarage product for a while, and it seems to …Participant. I agree with Jim. Most of the people using a RPi are likely to tinker with their installation. I – for my part – put a 128×64 SSD1306 OLED display (standard I2C) between the Pi and the acrylic … Troubleshooting and Technical help. OpenSprinkler 3.x Firmware Update Guide. View all 7. Weather and Integrations 6. Using Weather Adjustments. The Interactions between Rain Delay, Rain Sensor, and Weather Algorithm. Creating an IFTTT Applet to receive OpenSprinkler notifications. Using OpenSprinkler with Amazon Echo or Google Home Assistant. For Op e nS p r i nk l e r 2 . 3: plug in a wired Ethernet cable to OpenSprinkler's Ethernet jack, the other end to your router. If you prefer using WiFi connection, we recommend …One thing you can check is the wire resistance. Use an online calculator to compute the wire resistance, such as this one: keep in mind that you need to input the round-trip distance. Typical sprinkler valves draw about 200 to 300mA holding current, and if the voltage drops below 18V AC they are unlikely to stay on. Step 2: Attach OpenSprinkler to the wall, and re-inser t the wires: Refer to the Hardware Interface diagram and Zone Wire Connection diagrams on the previous pages. All terminal blocks on OpenSprinkler can be unplugged for easy wiring. To unplug, firmly grab both ends of the terminal block, wiggle, and pull it out. I am seeing this in the homeassistant log constantly not sure what is up. My open-sprinkler device is connected via Ethernet cable, I never have connectivity issues while hitting OS web gui. 2022-08-26 06:21:22.143 INFO (MainThread) [cus...Thanks in advance. Cheers. Tom. March 20, 2016 at 10:18 pm #41807. Ray. Keymaster. Yes, you will need a pump start relay (because a station on OpenSprinkler DC can only drive a load up to 1 amp max, if your pump requires 5 amp, you will need a relay). March 20, 2016 at 11:09 pm #41818. tom.farmer0.OpenSprinkler › Forums › OpenSprinkler Unified Firmware › Unable to load UI This topic has 16 replies, 5 voices, and was last updated 9 years, 6 months ago by Ray . Viewing 17 posts - 1 through 17 (of 17 total)Question about “NEW from OpenSprinkler v3.2: from v3.2, the controller has dual support for WiFi and wired Ethernet.” which as far as I can see is related to 2.2.0(1)s update to ESP8266 WiFi Core 3.0.2 and lwip as wired Ethernet library. I’m using ethernet. After upgrading firmware I’m seeing the AP mode running even when the … The OpenSprinkler web interface allows you to program water schedules and monitor station status through the web. Compared to traditional sprinkler timers, which limit you to a few buttons, dials, and a small screen, the web provides a much more intuitive user interface. You can access the controller using any device that has a built-in web ... Dec 30, 2022 · OpenSprinkler firmware is unified and can compiled under both Arduino environment and any Linux-based system. The instructions on this page are for the Arduino-based OpenSprinkler (OS 2.3, 3.x) only. If your controller is OpenSprinkler Pi (OSPi), please follow the OSPi firmware instructions to compile and run the firmware code.This video demonstrates the main features of OpenSprinkler Firmware 2.2.0. The content follows firmware 2.2.0 user manual, available at https://support.opens... OpenSprinkler is an open-source Internet web-based sprinkler timer / controller built upon the Arduino platform. Features of the app include: * Easy to understand device status. * Quick program modification. * Launch ad-hoc or defined programs instantly. * Manual mode for convenient testing. * Multi-device support. OpenSprinkler Station is for gaining advanced controls and status information over a single station (zone) of a device, e.g. to turn it on or off, or the time remaining. OpenSprinkler Device is for device-specific controls that usually apply to multiple stations or main unit sensors, e.g. if rain was detected. Compilation instructions for OS (Arduino-based OpenSprinkler) 2.3 and 3.x: * Install VS Code * Launch VS Code, search and install the platformio extension. * Download and unzip the OpenSprinkler firmware repository, open the folder in VS Code, at the bottom of the screen, click PlatformIO:Build. Aug 6, 2023 · Welcome to the OpenSprinkler application. This app only works with the OpenSprinkler controller which must be installed and setup on your home network. Purchase OpenSprinkler. OpenSprinkler.com Login. Scan For Device. Manually Add Device.Address OpenThings 5 Valley Lane Amherst, MA 01002 Email General Inquiry: [email protected] Orders: [email protected] Sales and Distribution: [email protected] Technical Support: support.opensprinkler.com NOTE: if you are seeking support for an existing product purchase from us, please submit a support ticket …Keymaster. 1. yes, it should work with OpenSprinkler. The output of this soil clik sensor is a relay which is a dry contact type. 2. no, this soil sensor is not a dry contact type, it requires an additional microcontroller to ‘interpret’ the result of the soil moisture value. It cannot be used directly with OpenSprinkler. Welcome to the OpenSprinkler application. This app only works with the OpenSprinkler controller which must be installed and setup on your home network. Purchase OpenSprinkler. OpenSprinkler.com Login. Scan For Device. Manually Add Device. Posts. As I understand things, WeatherUnderground has been bought out by IBM and is now a fee-based-only service. Since that happened, I know of several weather-data providers who have taken their data off WeatherUnderground and no longer provide data to that service. In order to keep OpenSprinkler completely open-source, perhaps a …September 29, 2022 at 11:14 am #74013. DWillys. Participant. I have a couple of the opensprinkler devices on my network. They’re set up to get their tcpip data via DHCP. In the interface I can’t find anywhere I can set the hostname so I can identify which device is which. I tried setting the hostname in the DHCP reservation (Option 12) but ...Dec 30, 2022 · OpenSprinkler firmware is unified and can compiled under both Arduino environment and any Linux-based system. The instructions on this page are for the Arduino-based OpenSprinkler (OS 2.3, 3.x) only. If your controller is OpenSprinkler Pi (OSPi), please follow the OSPi firmware instructions to compile and run the firmware code.Apr 14, 2022 · Its simple, after speaking with DAB , the pump regulates pressure in the line as the solenoids are opened by open sprinkler controller than pushes water to the desired zone. Once the zone solenoid turns off the water pressure in the line signals the pump to turn off. There is a delay of 10 sec which is standard from the manufacture and can be ... There are a bunch of kinds…. -two wire reverse polarity to open or close. -three wire, common and + to one ot open, + to the other to close. -two wire spring return – + to open, 0 to close. (more expensive but failsafe) 24vac dpdt relay driven by open sprinkler output, with a dc supply to drive the valves could be wired to any of these types.Nov 29, 2013 · OpenSprinkler Pi. Watch on. If you hate watering the garden but enjoy messing around with computers, OpenSprinkler Pi is a no-brainer. It’s the cheapest and most configurable system of its type I’ve come across, it’s open source (and this means that Ray’s not the only person working on it – tools from the community like Rich Zimmerman ... If our distributor is out of stock, you can also buy directly from this website (https://www.opensprinkler.com) — we ship directly to most countries in the world. Products. OpenSprinkler. Rated 5.00 out of 5 $ 150.00 – $ 193.00; OpenSprinkler Bee (OSBee) Rated 4.60 out of 5 $ 62.00 – $ 72.00; OpenSprinkler Pi (OSPi) · Keymaster. 1. yes, it should work with OpenSprinkler. The output of this soil clik sensor is a relay which is a dry contact type. 2. no, this soil sensor is not a dry contact type, it requires an additional microcontroller to ‘interpret’ the result of the soil moisture value. It cannot be used directly with OpenSprinkler.There are a bunch of kinds…. -two wire reverse polarity to open or close. -three wire, common and + to one ot open, + to the other to close. -two wire spring return – + to open, 0 to close. (more expensive but failsafe) 24vac dpdt relay driven by open sprinkler output, with a dc supply to drive the valves could be wired to any of these types.ESPToy v2. $ 12.99 9.99. ESPToy is a WiFi development board for ESP8266. Version 2.0 has on-board Neopixel color LED, mini buzzer, button, light sensor, LiPo battery jack and charging chip. It has built-in CH340 USB-serial and auto-reset circuit. It’s pre-flashed with a demo software written in Arduino with ESP8266 core.Announcing OpenSprinkler Firmware 2.2.0(1) December 30, 2022 Announcing OpenGarage Firmware 1.2.0 October 7, 2022 Learning Electronics — I/O expander options October 10, 2021Aug 25, 2013 · OpenSprinkler Pi is an extension board for Raspberry Pi (RPi) (all versions of RPi). It allows RPi to directly access and control sprinkler valves. NOTE: OSPi no longer comes with enclosure. Instead, the design of a 3D printable enclosure is provided, you can use it to print the enclosure yourself, or order it online, such as from jlcpcb.com. The OpenSprinkler firmware (written in Arduino) provides a rich set of features, including web-based user interface, interval programming, graphical preview, … OpenSprinkler Station is for gaining advanced controls and status information over a single station (zone) of a device, e.g. to turn it on or off, or the time remaining. OpenSprinkler Device is for device-specific controls that usually apply to multiple stations or main unit sensors, e.g. if rain was detected. For Op e nS p r i nk l e r 2 . 3: plug in a wired Ethernet cable to OpenSprinkler's Ethernet jack, the other end to your router. If you prefer using WiFi connection, we recommend …April 8, 2014 at 2:00 pm #22829. Austria. Member. Hi! I am an absolute beginner, when it comes to the RaspBerry. So I’m really glad that I managed to get the SD card with openSprinkler setup for my RaspBerry. But after booting into the shell, it stops prompting me for a password and an login. Can anybody help me out with the standard login ...May 16, 2020 · OpenSprinkler › Forums › Hardware Questions › Recommended flow meter This topic has 5 replies, 4 voices, and was last updated 3 years, 3 months ago by Ray . Viewing 6 posts - 1 through 6 (of 6 total)Check the program’s interval time — it should not be zero. If you just want the program to run once during a day, you can use a large interval (such as 23 hours). As long as the end time minus the start time is less than the interval time, the program will run only once (at the start time). From firmware 2.1.2, the settings for each program ...service: opensprinkler.set_water_level data: entity_id: sensor.opensprinkler_water_level water_level: 50 Set Rain Delay Example This sets the rain delay of the controller to 6 hours, i.e. all stations will stop and programs will not run until the rain delay time is over.A quick note that our Black Friday / Cyber Monday sales are on now: all OpenSprinkler products are shown in discounted prices right now, and the deal only lasts till Monday Nov 28. This is the only time of the year that we offer discounted pricing, so if you are interested in buying OpenSprinkler, grasp this chance and don’t let it slip away ...September 29, 2022 at 11:14 am #74013. DWillys. Participant. I have a couple of the opensprinkler devices on my network. They’re set up to get their tcpip data via DHCP. In the interface I can’t find anywhere I can set the hostname so I can identify which device is which. I tried setting the hostname in the DHCP reservation (Option 12) but ... So in case you are looking for a 24V AC relay to work with OpenSprinkler in order to switch high-voltage devices, this is an inexpensive (. 2. Schrack RT314524: This is a very small 24V AC relay that you can buy from Mouser or Digikey. It has a contact rating of 16A @ 250VAC, which is also plenty for common applications. There are a bunch of kinds…. -two wire reverse polarity to open or close. -three wire, common and + to one ot open, + to the other to close. -two wire spring return – + to open, 0 to close. (more expensive but failsafe) 24vac dpdt relay driven by open sprinkler output, with a dc supply to drive the valves could be wired to any of these types.I have an old Orbit 12 zone B-Hyve sprinkler controller, but its WiFi module broke. All I had to do was to create a cable to connect the Pi Zero to the header on the power board of the Orbit. This way, the whole Orbit control module is substituted by the OpenSprinkler Pi. Please, see the wiring diagram attached as an Excel spreadsheet.Mar 24, 2021 · Insert each wire and tighten them down with a small screwdriver. The red zone cables should be inserted into the corresponding zones (Zone 1 on the old system goes into #1 on OpenSprinkler). The black P/MV cable is your pump/master valve. Plug this into an available zone (either 7 or 8).Mar 25, 2021 · Part 2: Add OpenSprinkler Integration. Navigate to Configuration > Integrations > Add Integration. Search for OpenSprinkler. Next, add your OpenSprinkler IP address, login password, and controller name. MAC address can be left blank. Then, click Submit. Assign it to an area like your garage and click Finish.Posts. As I understand things, WeatherUnderground has been bought out by IBM and is now a fee-based-only service. Since that happened, I know of several weather-data providers who have taken their data off WeatherUnderground and no longer provide data to that service. In order to keep OpenSprinkler completely open-source, perhaps a …Basic features of the OpenSprinkler include: - AVR Atmega328 MCU running at 8MHz, compatible with the open-source Arduino software. - Microchip ENC28J60 Ethernet … OpenSprinkler is an open-source Internet web-based sprinkler timer / controller built upon the Arduino platform. Features of the app include: * Easy to understand device status. * Quick program modification. * Launch ad-hoc or defined programs instantly. * Manual mode for convenient testing. * Multi-device support. Sale! ESPToy v2. $ 12.99 9.99. ESPToy is a WiFi development board for ESP8266. Version 2.0 has on-board Neopixel color LED, mini buzzer, button, light sensor, LiPo battery jack and charging chip. It has built-in CH340 USB-serial and auto-reset circuit. It’s pre-flashed with a demo software written in Arduino with ESP8266 core.rummaging through the forums, it looks like opensprinkler is having issues with APIs disappearing from the weather sites they use. When setting up my system, I noticed that the weatherunderground API key will expire in six months. I run a local weather station that transmits its data to several weather sites, but is also locally accessible on ...Its simple, after speaking with DAB , the pump regulates pressure in the line as the solenoids are opened by open sprinkler controller than pushes water to the desired zone. Once the zone solenoid turns off the water pressure in the line signals the pump to turn off. There is a delay of 10 sec which is standard from the manufacture and can be ...A quick note that our Black Friday / Cyber Monday sales are on now: all OpenSprinkler products are shown in discounted prices right now, and the deal only lasts till Monday Nov 28. This is the only time of the year that we offer discounted pricing, so if you are interested in buying OpenSprinkler, grasp this chance and don’t let it slip away ...Nov 29, 2013 · OpenSprinkler Pi. Watch on. If you hate watering the garden but enjoy messing around with computers, OpenSprinkler Pi is a no-brainer. It’s the cheapest and most configurable system of its type I’ve come across, it’s open source (and this means that Ray’s not the only person working on it – tools from the community like Rich Zimmerman ... OpenSprinkler would have to be mapped to an external IP with Duckdns or something similar. The external address and port would then be mapped to the skill along with the MD5 password. Because of the required mapping, this would never be a skill approvable by Amazon for publication.Weight. 0.23 lbs. Dimensions. 6 × 4 × 1 in. Type. 883LM door button, 893MAX universal remote. Security+ 2.0 Adapter for OpenGarage. This is for Security+ 2.0 garage systems (which has a yellow learn button). There are two options to choose from: one is based on 883LM security+ 2.0 door button, the other is based on 893MAX universal remote. OpenSprinkler unchains you from your sprinkler or irrigation control box, enabling you to program, run, or stop zones at any time from anywhere. Whether you are at your desktop, laptop, tablet or phone; whether you are at home, office, or traveling on the road, you can access OpenSprinkler through any modern browser; or use our free apps ... Meet your New Sprinkler System. OpenSprinkler will improve your lawn, garden, or farm irrigation. Create custom programs and use our automatic weather-driven algorithms. …If our distributor is out of stock, you can also buy directly from this website (https://www.opensprinkler.com) — we ship directly to most countries in the world. Products. OpenSprinkler. Rated 5.00 out of 5 $ 150.00 – $ 193.00; OpenSprinkler Bee (OSBee) Rated 4.60 out of 5 $ 62.00 – $ 72.00; OpenSprinkler Pi (OSPi) Step 2: Attach OpenSprinkler to the wall, and re-inser t the wires: Refer to the Hardware Interface diagram and Zone Wire Connection diagrams on the previous pages. All terminal blocks on OpenSprinkler can be unplugged for easy wiring. To unplug, firmly grab both ends of the terminal block, wiggle, and pull it out. Mar 29, 2020 · Firmware tutorial video is available at www.opensprinkler.com . After the controller is powered on and establishes the WiFi connection, you can find out its client IP address on the LCD by clicking button B1. Also, the OpenSprinkler mobile app can automatically scan your local network to discover OpenSprinkler’s IP address.Jul 21, 2015 · At 12 volts, that’s 417 ma (each). So well within the maximum OpenSprinkler spec of 800 ma per channel. But, I think the sum is too much for the 16 mil triac gnd trace on the OpenSprinkler pcb. Alternately, I could put 2:1 transformers on the OpenSprinkler channel outputs. That way I wouldn’t have to hack the OpenSprinkler pcb.Mar 16, 2016 · Thanks in advance. Cheers. Tom. March 20, 2016 at 10:18 pm #41807. Ray. Keymaster. Yes, you will need a pump start relay (because a station on OpenSprinkler DC can only drive a load up to 1 amp max, if your pump requires 5 amp, you will need a relay). March 20, 2016 at 11:09 pm #41818. tom.farmer0.OpenSprinkler Pi is an extension board for the Raspberry Pi. It makes use of the Raspi's GPIO pins to directly interface with sprinkler valves. It features a... Welcome to the OpenSprinkler application. This app only works with the OpenSprinkler controller which must be installed and setup on your home network. Purchase OpenSprinkler. OpenSprinkler.com Login. Scan For Device. Manually Add Device. OpenSprinkler owners can use this solution to send their PWS weather observations onto a local Weather Service server. For more information on the "WeeWX Solution" click here. 4 ) Solutions for specific PWS (provided by OpenSprinkler Forum members) Davis Vantage: a solution for this PWS has been kindly provided by @rmloeb hereHi, There is option to connect 2 sensors for OSPi: 1. Rain Sensor (Then when it rainy day, and the water is open, it will close automate) 2. Land Sensor (That in computer I see when the land is dry). Regards. June 17, 2014 at 3:06 pm #27223.Regarding concurrent vs sequential running modes, currently the only option is to globally switch between the two (i.e. either all stations run sequentially, or all stations are allowed to run concurrently). There is currently no support for subsets of sequential groups. July 5, 2013 at 7:43 pm #24613. djMax.Weight. 0.23 lbs. Dimensions. 6 × 4 × 1 in. Type. 883LM door button, 893MAX universal remote. Security+ 2.0 Adapter for OpenGarage. This is for Security+ 2.0 garage systems (which has a yellow learn button). There are two options to choose from: one is based on 883LM security+ 2.0 door button, the other is based on 893MAX universal remote.A quick note that our Black Friday / Cyber Monday sales are on now: all OpenSprinkler products are shown in discounted prices right now, and the deal only lasts till Monday Nov 28. This is the only time of the year that we offer discounted pricing, so if you are interested in buying OpenSprinkler, grasp this chance and don’t let it slip away ... · Keymaster. 1. yes, it should work with OpenSprinkler. The output of this soil clik sensor is a relay which is a dry contact type. 2. no, this soil sensor is not a dry contact type, it requires an additional microcontroller to ‘interpret’ the result of the soil moisture value. It cannot be used directly with OpenSprinkler.
I, too, had this problem and found that the only solution was to reboot OpenSprinkler. I also run HomeSeer, and developed an event to recognize when OS was offline to warn me. I tried any number of approaches, including an access point that was just 10 feet away. I finally gave up and switched to OpenSprinkler Pi.. Tinkercade
If you have already installed opensprinkler firmware onto the Pi then you can select a station (click the associated cog). In the settings popup, click the Advanced tab and select “GPIO” as the station type. You can now select the gpio pin that you want to toggle when this station needs to water. Make sure you then wire up that gpio pin to ...Station 5. I want to be able to run both pumps at the same time, but stations sequential. For example. Both pumps stars at 6 am, and running time 1 hour per station. So at 6 am, pump1 starts and open station 1, pump2, at same time opens station 4. At 7, both pumps runing,station 1 closes, and 2 open. Similarly , station 4 turns off and 5 turns on.This way, when OpenSprinkler starts to run any program, or receives weather changes, it can send a web request to IFTTT, which further triggers a text message or push notification to your phone. Conversely, to use a Maker action, you can set IFTTT to send a web request to your gadget. This way, when it receives an associated trigger, it can ...PCA9555 and PCA9535 both have 16 I/O pins, and both use Totem-poll output, so they can both sink and source a large amount of current. They are used in the current OpenSprinkler 3.2 controller and zone expanders. The only difference between the two is that PCA9555 has built-in pull-up resistor while PCA9535 does not. Address OpenThings 5 Valley Lane Amherst, MA 01002 Email General Inquiry: [email protected] Orders: [email protected] Sales and Distribution: [email protected] Technical Support: support.opensprinkler.com NOTE: if you are seeking support for an existing product purchase from us, please submit a support ticket at support.opensprinkler.com and provide necessary information such ... The OpenSprinkler firmware (written in Arduino) provides a rich set of features, including web-based user interface, interval programming, graphical preview, …Mar 25, 2021 · Part 2: Add OpenSprinkler Integration. Navigate to Configuration > Integrations > Add Integration. Search for OpenSprinkler. Next, add your OpenSprinkler IP address, login password, and controller name. MAC address can be left blank. Then, click Submit. Assign it to an area like your garage and click Finish. OpenSprinkler Zone Expander. $ 49.00 – $ 50.00. OpenSprinkler Zone Expander provides an easy and inexpensive way to increase the number of stations for your OpenSprinkler. Each expander adds 16 zones. Please note that there is NO expander for OpenSprinkler Latch — the DC expander will NOT work with OpenSprinkler Latch. Jun 16, 2015 · The MAJOR reasons I bought an OpenSprinkler are the option to use my own WU weather station for input with the Zimmerman Method, the web interface, and the security of NOT having a device depending on the cloud like the Rachio and Blossom controllers. I assumed the Zimmerman method was based on scientific study of irrigation using past and ... Jun 1, 2016 · Lastly, GPIO15 is used by OSPi for RF Stations and so it is not made available for GPIO Stations via the UI. By default OSPi sets this pin low during initialisation so it is odd that connecting it to your relay board caused “chattering”. It should have resulted in either a constantly “on” relay (if active low) or a constantly “off ... OpenSprinkler Zone Expander. $ 49.00 – $ 50.00. OpenSprinkler Zone Expander provides an easy and inexpensive way to increase the number of stations for your OpenSprinkler. Each expander adds 16 zones. Please note that there is NO expander for OpenSprinkler Latch — the DC expander will NOT work with OpenSprinkler Latch. · There are many tutorial on how to do this. 2) Once you have a working raspbian and you are logged in, you need to install git by running. apt-get install git. 3) Change directory to /usr/local. cd /usr/local. 4) Clone the unified firmware repository. This will create a directory into /usr/local called OpenSprinkler.24VAC/500mA sprinkler transformer for OpenSprinkler AC and OpenSprinkler Pi. Please note that this plug is only for 110~120v U.S. outlets. Due to the low current rating (500mA), it is NOT suitable to run more than 2 valves at the same time (i.e. concurrent/simultaneous zones). If you need to run more zones at the same time, please find a 24VAC …Announcements, questions, and suggestions about the OpenSprinkler Unified firmware. Questions about hardware troubles and hardware design. Explore alternative firmware solutions and software extensions developed by the community. Make comments, suggestions, or request new features.Regarding concurrent vs sequential running modes, currently the only option is to globally switch between the two (i.e. either all stations run sequentially, or all stations are allowed to run concurrently). There is currently no support for subsets of sequential groups. July 5, 2013 at 7:43 pm #24613. djMax.OpenSprinkler Zone Expander. $ 49.00 – $ 50.00. OpenSprinkler Zone Expander provides an easy and inexpensive way to increase the number of stations for your OpenSprinkler. Each expander adds 16 zones. Please note that there is NO expander for OpenSprinkler Latch — the DC expander will NOT work with OpenSprinkler Latch.1) the clock on the controller’s display is frozen at a time earlier in the day. 2) none of the 3 buttons on the controller do anything. 3) the Ethernet module’s internal red LED is still on, and the 2 LEDs on the RJ45 jack seem to reflect normal network activity. 4) the controller still responds to pings. 5) if the controller was in the ....